• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix door hinge a Loose Door Hinge

Fixing a loose door hinge is a simple task for most homeowners. If the screws' holes have been stripped and will not hold screws, you may require dowels and wood glue in order to reinstall the hinge.

Before you do this, however, brush away surface rust. This will help to keep the dowels in place and provide a solid foundation for them to rest on.

Eliminating the Hinges

Many standard door hinges are able to be removed, [Redirect Only] making it easier to move the door from one side to the next or to remove the entire door off the frame, if needed. Anyone with a bit of patience can remove the hinges, but you must be aware of what to do.

If the hinges have been painted, you'll need to remove the paint before you attempt to remove the pins. If you do not, the paint may flake off and scratch your door when you try to lift it. To break the paint seal put the hinges into an stainless steel pan and fill the pan with water until the hinges are fully submerged. Let the hinges locks rest in the pan for about 30 minutes. The heat of the water will soften the paint, making it easier to take off.

Once the pins are loosened and the pins are loose, you can take off the hinges from the frame and upv door hinges. It is possible to use a regular screwdriver, however a magnetic screwdriver is recommended for this job. This type of screwdriver is specifically designed to take out screws made of metal and will help you get the job done much faster.

Before you attempt to remove the hinges, it is recommended to spray them with a grease. A simple lubricant will help you accelerate the process and make the removal of pins and screws with ease. You can find this kind of lubricant at a variety of hardware and home improvement stores.

The number of hinges you need will also differ based on the kind of door you have, and how it is set up. Solid-cored and heavier doors will require more hinges whereas lighter and hollow-cored doors may only require two or three hinges.

Understanding the different kinds of hinges can help you decide which one is the best for your needs. The hinges on the exterior are designed to withstand the weight of a door, but hinges for interior use must be able support lighter loads.

Reattaching the Hinges

Sometimes, a hinge on a door will become looser over time and begin to hang out of alignment or slide. This can cause problems but is usually easy to repair. Most of the time an easy tightening of the screw will fix the issue. However when the screw holes have been stripped out, it can be more difficult. Fortunately, there is a trick to get these holes tight again using a wooden dowel.

Begin by drilling out the hole from the previous one using a drill bit that is close to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length the same as the screw to ensure a snug fit. Then, you can reinstall the screw and tighten it to the desired tightness. If the door has the tendency to be bowed, then add another dowel to the gap and repeat the procedure. Close the door slowly after each adjustment to ensure the clearances around the perimeter are correct.

You can also use a wooden plug in place of the dowel. This is also a viable option however it may take a bit longer to install. You can insert a piece of wood that has been whittled to the right size. If you don't own a woodworking instrument or toothpicks, you can make use of toothpicks or matchsticks made from wood.

Make use of a countersink to make the hole smaller than the head of screw after you have reinstalled it. This will prevent the screw from rubbing against the edges of the doors when they are closed and opened. This will make it much easier to tighten the screws before reinstalling hinges.

After you have reinstalled the hinge, make sure to lubricate it with a dry lubricant in order to prevent it from getting stuck in the future. Products like PB Blaster or Liquid Wrench are great alternatives. Apply a thin layer of it and allow it to soak into the hinge barrel for around 15 minutes.

Refinishing the Hinges

If you are not ready to replace window hinges the hinges on your door, you could do a few simple repairs. The first step is to check whether the screws that secure the hinge plate to the door and frame are tight. If they're loose, tighten them with the help of a screwdriver or a power drill. Be cautious not to over tighten the screws, because this can cause gaps to form at the trim joints or worse, strip the threads.

If the issue is that the hinge plates are splitting and you want to reattach the plates by applying wood glue on the side of them and inserting toothpicks or wooden dowels into the holes. The dowels or toothpicks serve as a solid base for the screws and prevent the plates from shifting when you drive them into the holes. Allow the glue time to dry before reattaching the hinge.

The screws can also be smashed or gone. This problem can be fixed by replacing the screws. Make sure you use the correct drill bit for the size of the screw hole to avoid drilling into other parts of the jamb or hinge.

After you've reattached your hinge close the door and look at the gap between the door and the frame. The gap should be about the thickness of a penny or less if an older door was hung incorrectly. If the hinges were put in place correctly, this should not be a problem.

If you discover that the hinges are loose, try putting an extra thicker shim between the hinge plate and the mounting surface to add some extra space. You can also remove the hinge pin and then pound it down with a heavy hammer in order to tighten it, or install the hinge of a different type. You can also lubricate your hinges using mineral oil or jojoba in order to reduce friction and keep them in place. Lubricating your hinges frequently can stop them from becoming stiff and squeaky, and also prolong their lifespan.

Cleaning the Hinges

The friction created by a hinge's constant movement draws dust particles. Without periodic cleaning and lubrication, these particles become stuck in the moving parts of a hinge for doors and build up over time. In the end the hinge becomes stiff and creaky, and its appearance can be damaged quickly. Regular cleaning, lubrication, and inspection will preserve the quality and function of hinges on doors.

Examine the hinges to determine how much rust has built up on their surface. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you can save the hinges, begin by brushing off loose rust using steel wool and wire brushes. Apply a commercial rust-removing product or a homemade solution such as lemon juice to the hinge. Allow the rust remover to be on the hinge for a few minutes to dissolve and penetrate any remaining corrosion.

Retightening screws can restore hinge functionality in the event that you don't want to spend time or money on repairing hinges. If you've sanded the screw holes however, it could be necessary to attach the dowel of wood or shim to the hinge. Dowels made of wood are round pieces of wood that are in the form of rods which are available in different sizes and lengths. They are available at home improvement stores as well as woodworking supply and craft shops, or online.

You can also create a shim from a piece either plastic or metal, depending on the type of window hinge repair you own. To make a dowel, you need to cut an unfinished dowel into the desired length. You can then dip the dowel into carpenter's glue before inserting it into the cut hole, allowing the glue to hold the dowel in the desired position.

Before you begin cleaning the hinges, lay down a paper or cloth towel to protect flooring and other surfaces from spills and drips that may happen. After you have protected the area then clean the hinges using a soft sponge or a cloth that has been dipped in mild cleaner to get rid of dirt and grime. You can also remove tarnish, dirt, and grime. A small or toothbrush can be used to reach hard-to-reach areas in crevices and tight places.