• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Allowing your cat to come and go out of the home at its own pace is a great idea to keep it mentally and physically stimulated. Having a flap can also aid in reducing toilet accidents by making it easier for your cat to exit the house whenever it wants to.

Take a look at the Door

A cat flap allows your pet to come and go as they please without having to open the door for them. This is ideal to keep them in the house the home when you're away and helps to keep unwanted pests out of the home too!

You should measure the door to ensure you get the right size cat flap. There are various sizes available. You can then ensure that the cat flaps flap is the correct size for the door you have. Otherwise, it could be too large or small and your cat might have difficulty using it.

Use a ruler to determine the width at several locations along the edge of the door. You should also determine the door's height in a few places. This is because doors that are too high can cause your cat to perform an exercise routine like a gymnast every time they want to use the flap!

Get help from a glazier in case you're not sure what to measure for the door. They will be able to assist you in determining whether the door you have is suitable for a cat flap installation near me flap, and help you decide on the best size of flap to buy.

When you've got your measurements, the next step to do is mark the outline of the hole in the door. This will give you an outline to cutting the hole and will help you avoid making a mistake that could cost you money in the end!

You must also ensure that the hole you're creating is in the correct place. If you are fitting a cat flap in a upvc door a cat flap to a patio door it is important that the hole doesn't get too close to the hinges. This could result in leakage or problems with the seal.

If you have a glass door it is best to delegate this task to a glazier. It can be difficult to insert the cat flap onto an existing glass pane, and you may find that the process causes it to break and lose its weatherproof seal.

Measure the Cat

A cat flap lets your pet to go and come whenever they want without needing to leave them on their own. It can also help to keep draughts out of your house, which aren't bad for you or your cat!

If you own a uPVC door or composite, it might be difficult to install the cat flap. These doors are made of different materials and the installation is different. Before you decide to install the cat flap on your uPVC or composite door, make sure that it's compatible, and that you have consulted the manufacturer as any modifications could cause the warranty to be invalidated.

They are designed to be durable and tough with insulation. They are more resistant to the weather than other kinds of door, but it can be difficult to install an animal flap. If you're unsure about whether your replacement upvc door panel with cat flap or composite door will accommodate a cat flap, consult with a professional joiner prior to beginning.

To ensure that your cat can access the door, you'll need measure their height. It's easiest to measure their height when they're calm or asleep, so that they don't sway around. Once you know their height and weight, you can determine the distance between their stomachs and the floor to determine the position of the flap's bottom. This position can be outlined on the door.

If your uPVC or composite door is made from metal (either steel or aluminium) it is important to be extremely cautious when cutting it with power tools. Drilling into metal can cause it crack, especially when the area is made of toughened glass. This is the reason it's recommended to engage a glazier when installing your cat flap in a pane of glass. This will prevent the glass from becoming fragile or shattering. A Glazier will also be able to provide you with a circular cat flap hole that is less likely to break and is safer for your cat to use.

Cut the Hole

A good quality cat flap comes with a drawing template that you can use to mark the spot on your door where the hole will be. If it isn't, you can make one using the thin paper (tracing paper is a good choice). After the shape is pencilled in on the door, you can then use a spirit level to make sure that the shape is completely horizontal. This will allow your cat flap to properly fit into the door and prevent it from being able to slide open or close.

Next, take your jigsaw and cut the shape written on the door. Make sure that you're using a blade suitable for use on uPVC doors. Usually, it will be labelled accordingly If not, ask the staff at your DIY store for advice. After the hole has been cut and the flap is placed against it and open it, making sure that the flap is moving smoothly. If it is bound at any point, use a file or rasp to fix it.

You should also check that there are no electric gas or cable lines within the door you'll be cutting through, since they could be damaged by your Jigsaw. Additionally, you should be aware of any handles or other fixtures on the door which will need to be removed in order to fit the cat flap install flap and be careful not to harm them during this process.

The majority of people who install the cat flap themselves have an ordinary solid uPVC door and so won't have to deal with any of these problems. But, if your door is made of timber or has decorative panels that cannot be removed, it will increase the difficulty of the task.

For these kinds of jobs, it's recommended to seek out expert advice from a cat-flap fitter. It is important to do them correctly to avoid problems in the future. If you do it wrong, it could cause the door to be damaged and could make it impossible to honor the warranty.

Fit the Flap

Once you have cut your hole, place the flap to see if it opens and fits. If you notice any spots that catch or stick, file them down with a hand file or sandpaper until it fits correctly and opens without issue. Make sure the flap is flush with the door.

Some kits come with templates for this, however, if it doesn't, you can use a piece or thin paper instead - something similar to tracing paper. Place the paper on the door, and draw a line in order to indicate where the flap should be placed (this will serve as a cutting guide). Draw four screw holes at each corner of the flap with the pencil marks you traced on the door. These will be the screw holes you'll need to fix the flap in place.

Most uPVC doors are solid and therefore easy to cut into. If your door is made of composite or GRP however, it could be more difficult. If you're not experienced with this then it may be beneficial to engage a professional to handle the work for you. They will also be able to tell you if your door is suitable for the installation of an animal flap.

If you're planning to install a cat flap into composite doors, it is important to first confirm the manufacturer or a professional joiner. Any modifications made to these doors may make it impossible to honor the warranty. If you decide to complete the work yourself, keep in mind that it could be a messy job and may even be hazardous.

When you have composite doors, you'll generally need to use the aid of a saw or grinder to cut through the door panel itself instead of just cutting through the GRP. Be aware that this could be extremely dangerous work and you'll have to take extreme care not to hurt the door or yourself, as it is very fragile. It's also important to note that cutting holes into any kind of glass door is much more difficult than making the same changes in a uPVC or Fitting a cat flap In a upvc door solid wooden door.