• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace lock on upvc door Door Locks

Door locks are your primary security measure against unauthorized access to your home. Signs of wear and tear, and also instances like moving into a new residence or break-ins, can necessitate the necessity of replacing your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will assist you select the appropriate lock.

Deadbolt

If you want to ensure your door is secure against intruders, it's a good idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe it makes it more difficult for an intruder to get through the door. A single cylinder deadbolt can be activated using keys on the exterior side and a thumb turn device on the interior. A deadbolt will only work if it's installed correctly however.

It is first necessary to find out if the door has an existing hole for a deadbolt, or if you need to bore it out. Mark the position of the hole for the deadbolt on the exterior of the door by using the template supplied with the lock installation set. Then, use the tape measure to determine the height the deadbolt needs to be. Then, mark the height on the side of the door. You can then use a speed square to draw an even line across the mark you made for the bolt hole.

Then using the power drill, drill through the hole until it is on the opposite side of the door. This could take a bit of time. Sand the hole and the edge of the door to make it smooth. It's also recommended to paint or Replace Door Lock stain the door at this point.

When the door is open, remove any screws visible on the deadbolt. This will reveal the back and front assemblies of the deadbolt as well as the bolt that is inside. Then, unscrew the bolt and replace it with a new one that matches your door hardware. It is necessary to remove the bolt from a setplate. After this, you'll need to chisel the door frame for the strike plate.

If your strike plate isn't aligned properly, it's likely because the previous installer didn't properly mortise it or a weatherstripping popped up and changed the strike's position. You will need to re-mortise the strike plate and perhaps even the deadbolt to fix this issue. Close and lock the deadbolt when you've completed this step. Test the deadbolt by closing and locking it once the bolt has been extended into the strike plate.

Knob

It can make your home or business less secure if the door knob is worn. It may also make it harder to open or close the door, which is why it's an ideal idea to replace door lock it. Replacing a knob is a relatively easy DIY project and shouldn't take more than 30 minutes to complete. Use a screwdriver or pliers to remove any knobs or handles. Be cautious not to damage other components of the door.

Spray WD-40 or another dry lubricant on the mechanism of your door knob prior to you begin. This will allow the new lock to slide effortlessly as you turn it. To ensure that it operates properly, it's important to choose the knob and handle that match the doors you already have. If you don't already have a doorknob that is compatible and handle, you'll need to purchase a replacement.

Before you begin the replacement, look over the knob you replaced to determine what screws are that are holding it in place. If there aren't any screws, you can use a screwdriver to wedge between the cover plate and the plate with hidden screws and then remove it.

After you have removed the knob take it apart and look for signs of rust and damage. If the knob is damaged or has dents or marks then you'll need clean it. Otherwise, it shouldn't require any major work.

Install the new knob. It is important to first look over the two knobs in order to make sure that you've chosen the right one for the door. You should select one with an extended rod that is designed to lock replacement upvc door with the second knob's rod mechanism. After you've placed the new knob over the hole in the door and then carefully slide it into the latch.

Thread the latch plate screws downwards, then test the spring by pushing down on it repeatedly. The latch should spring up each time. Then, you can install the new knob and connect it to the rod mechanism on the previous knob. Thread the long screws of the interior doorknob into the holes for the cylinder on the outside knob and fix it in the knob's position.

Latch

A latch is a metal piece that extends into the doorjamb to secure it closed. The latch can be operated by a knob or handle located inside the door, or a thumb-turn on the exterior. The latch can be secured using a deadbolt to keep intruders from breaking in through the glass of the door. It also provides protection from accidental or intentional closing of the door by pets or children. You can choose to install an entry point with either a single-cylinder deadbolt or double-cylinder deadbolt, depending on the level of security.

Installing a latch requires the same steps like installing a deadbolt however, there are a few variations. To make sure that the new lock is compatible, first take a measurement of the setback on the doorjamb using a tape measure. The setback is the distance from the edge of the doorjamb, to the center of the hole that will be used for the latch faceplate. The standard setback is 2 3/8 to 2. 3/4 inches. If your setback is larger than that, you might need to purchase a latch that is longer from a locksmith or hardware store.

Then, drill a hole for the latch plate into the doorjamb's edge. Use a chisel and cut the mortise of the latch. Make sure the depth is enough for the faceplate to be in line with the doorjamb. Tape the strikeplate to the doorjamb to ensure it is positioned correctly.

If the strike is too high, you can push the door back or apply pressure with a tire iron or crowbar. This could also cause cracks in the doorjamb. This can be corrected by drilling a new hole into the doorjamb, and removing the core from the previous one.

Installing the new strike plate is the final step. This can be accomplished by fixing the new plate to the existing screw holes. Utilize wood putty to fill in any old bolt holes or screw holes which aren't going to be used. Once the putty is dry you can sand replace door lock it down to give it a an elegant finish.

Strike

An electric strike is the metallic piece where the deadbolt and latch engage when the door is closed. It is a crucial component of the overall security of a lock because it seals the door and also provides additional resistance to force or kicking applied to the door. If a door has been equipped with an electric strike, it can only be opened using a key or the control unit which controls its electrical impulses.

Traditionally the installation of an electric strike meant cutting a section of the doorjamb in order to remotely release the latchbolt of a cylindrical lock from the pocket within the strike. This is a drawback in regards to the appearance of an opening, and it also exposes the mechanism of the latchbolt and keeper to unintentional users.

Recently, several electric strike makers have come up with an innovative type of electric strike called the "No Cut" strike that doesn't require cutouts in the doorjamb to function. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without causing damage to the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the keeper and latchbolt when it receives an electrical signal from a controller or reader. The retracting of the keeper as well as latchbolt causes them to rise on the ramp, thereby locking the composite door replacement lock. When the door is shut, the deadbolt stays at a lower position and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy process, particularly in the case of replacing lock on upvc door an existing strike door. If you're planning to upgrade an existing access control system to an electric strike, it is important to ensure that your new system is compatible. You will also need to make sure that the strike is wired to your access control system and is set up for fail-safe operation.

Upgrade your strike plates to high duty strike plates to block unauthorized entry. These plates use four to six three-inch screws instead of the two three-fourth inch screws that are typically used in standard strikes. These screws are longer and make breaking the frame to reach the thumb turn piece on a single cylinder deadbolt more difficult.